Dakota-digital MCL-3207 Bedienungsanleitung PDF herunterladen

MAN# 650305:E

MODEL MCL-3207

3-3/8” SPEEDOMETER/TACHOMETER for 2008-2010 Rocker

GAUGE SETUP AND CALIBRATION

The setup menus are entered by holding the switch in while turning the key on. The menus are as follows:

Menu Description

dIag (EngInE, seCURE, ABS, DONE) read diagnostic codes

ADJvST (FASTER, SLOWER) (75 - 125) adjust calibrate speed

vnIt (MPH, km/h ) select speed & temp unit

S SET (OFF, 500 - 7500) miles to service setting

PERF (ON, OFF) turn on/off performance displays

NIGHT (ON, OFF) turn on/off automatic night dimming

WXARN

RPM

(shown on bar graph) set RPM shift warning point

WXARN

(9.0- 12.1) set low volt warning point

HI F-C (200F - 420F or 93C - 215C) set temperature warning point

GEAR (DONE, PRESET, LEARN) transmission gear display selection

FUEL (OFF, SPO, CST, dyn, d09) select fuel sender type

(SET LO, range, DONE) low fuel light and range setup

CL CAL adjust clock calibration

INFO display gauge revision code on speedometer

odoMK- one-time odometer preset

POWER & GROUND

The gauge is a direct plug in. Constant battery power and key switched power are supplied by the stock

harness along with ground.

STATUS AND WARNING INDICATORS

Several indicators are supplied on the stock wiring harness. Some of these may not be active on your

motorcycle. These include the security, engine, ABS, and low fuel.

LOW VOLTAGE WARNING

When the voltage drops below the warning limit with the engine running, LO and your current voltage will be

displayed. (default warning limit is 11.0V)

SPEEDOMETER & TACHOMETER

The speedometer and tachometer signals are read from the engine control module (ECM) over a data bus.

The speed can be calibrated to allow for differences in tires or gearing; calibration is discussed later.

The tach bar displays RPM x1000 with a range of 7000 RPM. The RPM can also optionally be shown on the message

display.

CLOCK

The clock uses a 12 hour format and can be set by pressing and holding the switch while the clock is displayed.

After the switch is held for a few seconds the hours will begin flashing. Momentarily pressing the switch will change the

hours, holding the switch will move to the minute set, and the minutes will begin flashing. Momentarily pressing the

switch will now change the minutes. Holding the switch will exit the clock set mode.

MOUNTING

The gauge will mount into the original housing using original grommet, screws, and mounting clip. Remove the

stock gauge by pulling it out of the housing using a slight rocking motion; it is held in place by a plastic mounting clip on

the back of the gauge. Once out, remove the two screws from the back of the mounting clip, then unplug the gauge.

Remove the grommet from the stock gauge and install it over the MCL-3207. Plug in the MCL-3207 and secure the

mounting clip with the two screws. Push the gauge firmly back into the hole making sure the clip lines up with the slots

in the dash and also watching that wires are not damaged or pinched. (see photos below and on next page)

IMPORTANT NOTE! This gauge has an odometer preset option that is only available one time in the first 100 miles

(160km) of operation. See “Odometer preset” for instructions.

B V

MPH

km/h

RPM

1 2 3 4 5 6

Inhaltsverzeichnis

Seite 1 - MODEL MCL-3207

MAN# 650305:E MODEL MCL-3207 3-3/8” SPEEDOMETER/TACHOMETER for 2008-2010 Rocker GAUGE SETUP AND CALIBRATION The setup menus are entered by ho

Seite 2 - MAN# 650305:E

MAN# 650305:E SPEEDOMETER SETUP Press and hold the switch while turning the key on and starting the engine. Once the engine is runn

Seite 3

MAN# 650305:E S SET S SET S SET S SET Miles to Next Service setup The service mileage is a countdown mile meter. The service mile display can be

Seite 4

MAN# 650305:E teMKPteMKPteMKPteMKP Temperature warning setup • Press and release the switch until “TEMKP” is displayed, then press and hold the

Seite 5 - Troubleshooting guide

MAN# 650305:E FUNCTION SWITCH The function switch on the side of the dash panel allows access to all of the mileage, RPM, and performance infor

Seite 6

MAN# 650305:E SERVICE AND REPAIR DAKOTA DIGITAL offers complete service and repair of its product line. In addition, technical consultation is

Kommentare zu diesen Handbüchern

Keine Kommentare

Dakota-digital MCL-3207 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Dakota-digital MCL-3207 herunter. Dakota Digital MCL-3207 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Dakota-digital MCL-3207